Cisco WLC
Last updated
Was this helpful?
🇬🇧 English
Last updated
Was this helpful?
The below instruction pertains to Cisco WLCs of 2504 and 5520 series with IOS 8.2.166.0
Social WiFi has been tested and is proven to work on the following configurations:
Cisco 2500 Series Wireless Controller
versions up to 8.5.131.0
Cisco AIR-CAP3702I-E-K9
versions compatibile with the Controller
Log in to the administrative panel with root permissions and press Advanced.
RADIUS configuration
Security → AAA → Radius → Authentication
Security → AAA → Radius → Authentication → New
Server Index (Priority)
Leave default (1)
Server IP Address
35.205.62.147
Shared Secret Format
ASCII
Shared Secret
Confirm Shared Secret
Key Wrap
Leave unchecked
Port Number
31812
Server Status
Enabled
Support for CoA
Disabled
Server Timeout
5 seconds
Network User
Unchecked
Management
Unchecked
Management Retransmit Timeout
Leave default (2)
IPSec
Leave unchecked
Press Apply.
Now, configure as follows:
Auth Called Station ID Type
AP MAC Address
Use AES Key Wrap
Leave unchecked
MAC Delimiter
Hyphen
Framed MTU
1300
Press Apply.
Now, in the menu on the left go to the AAA → Radius → Accounting tab and add new accounting server.
Server Index (Priority)
Leave default (1)
Server IP Address
35.205.62.147
Shared Secret Format
ASCII
Shared Secret
Radius Secret available in Access Points tab of the Social WiFi Panel
Confirm Shared Secret
Radius Secret available in Access Points tab of the Social WiFi Panel
Port Number
31813
Server Status
Enabled
Server Timeout
5 seconds
Network User
Leave unchecked
IPSec
Leave unchecked
Press Apply.
DNS Walled Garden Configuration
Now, go to the Access Control Lists → Access Control Lists in the same tab and press New... to add a new list.
Access Control List Name
sw_walledgarden
ACL Type
IPv4
Press Apply.
Hover the coursor over the blue icon on the right side of sw_walledgarden text and press “Add/Remove URL”.
Add these entries one by one:
socialwifi.com
sw-login.com
facebook.com
fbcdn.net
twitter.com
twimg.com
linkedin.com
licdn.com
accounts.google.com
accounts.google.*
ssl.gstatic.com
fonts.gstatic.com
fonts.google.com
accounts.youtube.com
googleapis.com
apis.google.com
connect.facebook.net
www.googletagmanager.com
www.googleadservices.com
googleads.g.doubleclick.net
Cisco WLC has a limit of 20 entries for URL ACL and the above list doesn’t include rules for a YouTube widget on the login splash page. If you want to use this widget, please contact us.
Captive Portal/Hotspot configuration
Now, go to the Security -> Web Auth → Web Login Page and configure as follows:
Web Authentication Type
External (Redirect to external server)
Redirect URL after login
[leave empty]
External Webauth URL
https://login.socialwifi.com/
Press Apply.
Go to Management → HTTP-HTTPS and disable WebAuth SecureWeb and HTTPS Redirection:
WebAuth SecureWeb
Disabled
HTTPS Redirection
Disabled
From now on you'll probably be prompted that you must reboot the device in order for the changes to take place. You can proceed with the guide and reboot the device after everything is configured.
Press Apply.
In the Controller → Interfaces section, make sure that the “virtual” interface’s address is not set to 1.1.1.1 (it used to be the default value). If it is, change it to 192.0.2.1.
Network settings configuration
Now, go to the WLANs → WLANs and create the WLAN network or edit if you already have one.
On the upper right press the Go button next to "Create New".
Press Apply.
Edit your WLAN and go to security Layer 2 tab. Set "Layer 2 Security" as None.
Next, go to the Layer 3 tab and configure as follows:
Layer 3 Security
Web Policy
*Check the box*
Authentication
Preauthentication ACL
IPv4 sw_walledgarden
IPv6
None
WebAuth FlexAcl
None
Sleeping Client
Leave unchecked
Over-ride Global Config
Leave unchecked
Go to AAA Servers tab and configure as follows:
Authentication Servers Enabled
Yes
Server 1
IP:35.205.62.147, Port:31812
Accounting Servers Enabled
Yes
Server 1
IP:35.205.62.147, Port:31813
Radius Server Accounting Interim Update
Yes
Radius Server Accounting Interim Interval
600
Press Apply.
After completing the authorization process you will see a "logout" tab open. It can be disabled using an CLI command:
"config custom-web logout-popup disable"
Monitor → Access Points → Radios → 802.11a/n/ac or 802.11b/g/n
Copy the MAC addresses of the Access Points you would like to add to Social WiFi platform.
Go to the Social WiFi Panel.
Choose the place to which you would like to add the device.
In the “Access Points” tab, press “Add” (upper right corner), paste the MAC address you copied into the form (adding a name is optional) and click “Create”.
Thats the end of the configuration and you can test the service by logging in through your Access Point.
Radius Secret available in Access Points tab of the
Radius Secret available in Access Points tab of the
