Skip to content

Teltonika

Prerequisites

Please switch to the “Advanced settings” as shown below.

2025-07-02_13-08.png

Compatibility

Device models:

  • all Teltonika devices that can run the firmware versions 00.07+

Firmware versions:

  • 00.07+ (tested up to 00.07.06.18)

Package installation

First, ensure that you have “Hostpot” package installed. In order to install the package, go to System -> Package Manager -> Packages. Search for “Hotstpot” and click Install under the “Actions” colon to install the Package.

2025-07-02_13-12.png

You will see a pop up window, click Continue and wait for the installation to complete.

2025-07-02_13-13.png

Please note this might take a couple minutes. You should see that the package has been installed:

2025-07-02_13-16.png

After the installation is complete, and you still can’t see the Hotspot menu, please reboot the router.

SSID configuration

Go to Network -> Wireless -> SSIDs and click Add.

2025-07-02_15-36.png

You will see a pop up window. In the General Setup tab configure as follows:

Enableon
ModeAccess Point
SSIDYour SSID name
PasswordLeave empty
Network— No network —

2025-07-02_15-39.png

Now, switch to the Wireless Security tab and from the Encryption drop down menu select “No encryption”:

2025-07-02_15-39_1.png

Click Save & Apply. You should now see that the new SSID has been created and enabled:

2025-07-02_15-39_2.png

Hotspot configuration

Now, go to Services -> Hotspot -> General.

Under the “Add new instance” tab, from the Interface drop down menu select your SSID created in the previous step.

2025-07-02_15-40.png

Click Add:

2025-07-02_15-40_1.png

You will see a pop up window. In the General tab, configure as follows:

Configuration profileDefault
Enableon - this will be available after changing “Authentication mode” to Radius
Hotspot network192.168.2.0/24 - the default value, feel free to change
IP address192.168.2.254 - the default value, must match Hotspot network
Authentication modeRadius
Landing pageExternal
Password encodingon
Landing page addresshttp://login.socialwifi.com
UAM port3990
UAM secretLeave empty
Success pageOriginal URL

2025-07-02_15-42.png

Now, switch to the Radius tab and configure as follows:

RADIUS server #135.205.62.147
RADIUS server #235.205.62.147
Authentication port31812
Accounting port31812
NAS identifierLeave empty
Radius secret keyRADIUS Secret is available in Access Points tab of the Social WiFi Panel
Swap octetsoff
Location nameLeave empty
Location IDLeave empty

2025-07-02_15-44.png

Next, switch to the Walled garden tab. Make sure that Mode is set to “Allowlist”, copy and paste the below:

login.socialwifi.com
sw-login.com
connect.facebook.net
www.facebook.com
www.facebook.com
facebook.com
static.xx.fbcdn.net
external-frt3-2.xx.fbcdn.net
twitter.com
api.twitter.com
x.com
api.x.com
pbs.twimg.com
abs-0.twimg.com
abs.twimg.com
linkedin.com
www.linkedin.com
static-exp1.licdn.com
media-exp1.licdn.com
static.licdn.com

2025-07-02_15-47.png

Click Save & Apply.

Adding the MAC address to the panel

Go to Network -> LAN and copy the MAC address of the your LAN interface. Screenshot for reference below.

2025-07-02_16-44png

Now, switch to Social WiFi Panel, go to Access Points tab, click the Add button and paste the MAC addresses of Teltonika router. Click Create.

Test the solution

Connect with the WiFi network. You should see a login page. Go through the login process and, once finished, you should have internet access. You should see first connections and authorizations in the Social WiFi Panel’s statistics section.